Thursday, September 27, 2018

Radio Network Unavailability Rate

Description

The Radio Network Unavailability Rate KPI indicates the percentage of time when cells in a radio network are unavailable. This KPI is used to evaluate the deterioration of network performance caused by unavailable cells on the radio network during busy hours.

Definition

The Radio Network Unavailability Rate KPI is defined in Table 1. This KPI is calculated based on the length of time all cell services are unavailable on the radio network.

Table 1 Radio Network Unavailability Rate
Name Radio Network Unavailability Rate
Object Radio network
Formula RAN_Unavail_Rate = (ΣCellUnavailTime/(TheTotalNumberOfCellsInCluster x {SP} x 60)) x 100%
NOTE:
"SP" indicates the reporting period for counters in minutes.
Associated Counters Radio Network Unavailability Rate =((L.Cell.Unavail.Dur.Sys + L.Cell.Unavail.Dur.Manual)/(Number of cells x {SP} x 60)) x 100%
"SP" indicates the reporting period for counters in minutes.
Unit/Range Percentage (%)

Radio Network Unavailability Rate -- LTE

Radio Network Unavailability Rate

Description

The Radio Network Unavailability Rate KPI indicates the percentage of time when cells in a radio network are unavailable. This KPI is used to evaluate the deterioration of network performance caused by unavailable cells on the radio network during busy hours.

Definition

The Radio Network Unavailability Rate KPI is defined in Table 1. This KPI is calculated based on the length of time all cell services are unavailable on the radio network.

Table 1 Radio Network Unavailability Rate
Name Radio Network Unavailability Rate
Object Radio network
Formula RAN_Unavail_Rate = (ΣCellUnavailTime/(TheTotalNumberOfCellsInCluster x {SP} x 60)) x 100%
NOTE:
"SP" indicates the reporting period for counters in minutes.
Associated Counters Radio Network Unavailability Rate =((L.Cell.Unavail.Dur.Sys + L.Cell.Unavail.Dur.Manual)/(Number of cells x {SP} x 60)) x 100%
"SP" indicates the reporting period for counters in minutes.
Unit/Range Percentage (%)

CSFB Success Rate Based Handover (LTE to CDMA2000)

Description

The CSFB Success Rate Based Handover (LTE to CDMA2000) KPI indicates the success rate of handover-based LTE-to-CDMA2000 CSFB.
The number of handover-based LTE-to-CDMA2000 CSFB attempts increases by 1 at point B as shown in Figure 1 after the eNodeB sends a Mobility From EUTRA Command message to the UE and performs CSFB to a CDMA2000 network. The number of successful handover-based LTE-to-CDMA2000 CSFB executions increases by 1 at point C, where the eNodeB receives a UE CONTEXT RELEASE COMMAND message from the MME after the UE successfully accesses the CDMA2000 network.

Definition

The CSFB Success Rate Based Handover (LTE to CDMA2000) KPI is defined in Table 1. The number of handover-based LTE-to-CDMA2000 CSFB attempts and the number of successful handover-based LTE-to-CDMA2000 CSFB executions are collected as described in Description.
Table 1 CSFB Success Rate Based Handover (LTE to CDMA2000)
Name CSFB Success Rate Based Handover (LTE to CDMA2000)
Object Cell or radio network
Formula CSFB_L2C_BasedHO_SR = (CSFB_L2C_BasedHO_Success/CSFB_L2C_BasedHO_Attempt) x 100%
Associated Counters CSFB Success Rate Based Handover(LTE to CDMA2000) =(L.IRATHO.E2C.CSFB.ExecSuccOut/L.IRATHO.E2C.CSFB.ExecAttOut) x 100%
Unit/Range Percentage (%)

CSFB Success Rate Based Handover (LTE to CDMA2000)

CSFB Success Rate Based Handover (LTE to CDMA2000)

Description

The CSFB Success Rate Based Handover (LTE to CDMA2000) KPI indicates the success rate of handover-based LTE-to-CDMA2000 CSFB.
The number of handover-based LTE-to-CDMA2000 CSFB attempts increases by 1 at point B as shown in Figure 1 after the eNodeB sends a Mobility From EUTRA Command message to the UE and performs CSFB to a CDMA2000 network. The number of successful handover-based LTE-to-CDMA2000 CSFB executions increases by 1 at point C, where the eNodeB receives a UE CONTEXT RELEASE COMMAND message from the MME after the UE successfully accesses the CDMA2000 network.

Definition

The CSFB Success Rate Based Handover (LTE to CDMA2000) KPI is defined in Table 1. The number of handover-based LTE-to-CDMA2000 CSFB attempts and the number of successful handover-based LTE-to-CDMA2000 CSFB executions are collected as described in Description.
Table 1 CSFB Success Rate Based Handover (LTE to CDMA2000)
Name CSFB Success Rate Based Handover (LTE to CDMA2000)
Object Cell or radio network
Formula CSFB_L2C_BasedHO_SR = (CSFB_L2C_BasedHO_Success/CSFB_L2C_BasedHO_Attempt) x 100%
Associated Counters CSFB Success Rate Based Handover(LTE to CDMA2000) =(L.IRATHO.E2C.CSFB.ExecSuccOut/L.IRATHO.E2C.CSFB.ExecAttOut) x 100%
Unit/Range Percentage (%)

CSFB Success Rate Based Handover (LTE to TD-SCDMA)

Description

The CSFB Success Rate Based Handover (LTE to TD-SCDMA) KPI indicates the success rate of handover-based LTE-to-TD-SCDMA CSFB.
The number of handover-based LTE-to-TD-SCDMA CSFB attempts increases by 1 at point B as shown in Figure 1 after the eNodeB sends a Mobility From EUTRA Command message to the UE and performs CSFB to a TD-SCDMA network. The number of successful handover-based LTE-to-TD-SCDMA CSFB executions increases by 1 at point C, where the eNodeB receives a UE CONTEXT RELEASE COMMAND message from the MME after the UE successfully accesses the TD-SCDMA network.

Definition

The CSFB Success Rate Based Handover (LTE to TD-SCDMA) KPI is defined in Table 1. The number of handover-based LTE-to-TD-SCDMA CSFB attempts and the number of successful handover-based LTE-to-TD-SCDMA CSFB executions are collected as described in Description.
Table 1 CSFB Success Rate Based Handover (LTE to TD-SCDMA)
Name CSFB Success Rate Based Handover (LTE to TD-SCDMA)
Object Cell or radio network
Formula CSFB_L2T_BasedHO_SR = (CSFB_L2T_BasedHO_Success/CSFB_L2T_BasedHO_Attempt) x 100%
Associated Counters CSFB Success Rate Based Handover(LTE to TD-SCDMA) = (L.IRATHO.E2T.CSFB.ExecSuccOut/L.IRATHO.E2T.CSFB.ExecAttOut) x 100%
Unit/Range Percentage (%)

CSFB Success Rate Based Handover (LTE to TD-SCDMA)

CSFB Success Rate Based Handover (LTE to TD-SCDMA)

Description

The CSFB Success Rate Based Handover (LTE to TD-SCDMA) KPI indicates the success rate of handover-based LTE-to-TD-SCDMA CSFB.
The number of handover-based LTE-to-TD-SCDMA CSFB attempts increases by 1 at point B as shown in Figure 1 after the eNodeB sends a Mobility From EUTRA Command message to the UE and performs CSFB to a TD-SCDMA network. The number of successful handover-based LTE-to-TD-SCDMA CSFB executions increases by 1 at point C, where the eNodeB receives a UE CONTEXT RELEASE COMMAND message from the MME after the UE successfully accesses the TD-SCDMA network.

Definition

The CSFB Success Rate Based Handover (LTE to TD-SCDMA) KPI is defined in Table 1. The number of handover-based LTE-to-TD-SCDMA CSFB attempts and the number of successful handover-based LTE-to-TD-SCDMA CSFB executions are collected as described in Description.
Table 1 CSFB Success Rate Based Handover (LTE to TD-SCDMA)
Name CSFB Success Rate Based Handover (LTE to TD-SCDMA)
Object Cell or radio network
Formula CSFB_L2T_BasedHO_SR = (CSFB_L2T_BasedHO_Success/CSFB_L2T_BasedHO_Attempt) x 100%
Associated Counters CSFB Success Rate Based Handover(LTE to TD-SCDMA) = (L.IRATHO.E2T.CSFB.ExecSuccOut/L.IRATHO.E2T.CSFB.ExecAttOut) x 100%
Unit/Range Percentage (%)

CSFB Success Rate Based Handover (LTE to GSM)

Description

The CSFB Success Rate Based Handover (LTE to GSM) KPI indicates the success rate of handover-based LTE-to-GSM CSFB.
The number of handover-based LTE-to-GSM CSFB attempts increases by 1 at point B as shown in Figure 1 after the eNodeB sends a Mobility From EUTRA Command message to the UE and performs CSFB to a GSM network. The number of successful handover-based LTE-to-GSM CSFB executions increases by 1 at point C, where the eNodeB receives a UE CONTEXT RELEASE COMMAND message from the MME after the UE successfully accesses the GSM network.

Definition

The CSFB Success Rate Based Handover (LTE to GSM) KPI is defined in Table 1. The number of handover-based LTE-to-GSM CSFB attempts and the number of successful handover-based LTE-to-GSM CSFB executions are collected as described in Description.

Table 1 CSFB Success Rate Based Handover (LTE to GSM)
Name CSFB Success Rate Based Handover (LTE to GSM)
Object Cell or radio network
Formula CSFB_L2G_BasedHO_SR = (CSFB_L2G_BasedHO_Success/CSFB_L2G_BasedHO_Attempt) x 100%
Associated Counters CSFB Success Rate Based Handover(LTE to GSM) = (L.IRATHO.E2G.CSFB.ExecSuccOut/L.IRATHO.E2G.CSFB.ExecAttOut) x 100%
Unit/Range Percentage (%)

CSFB Success Rate Based Handover (LTE to GSM)

CSFB Success Rate Based Handover (LTE to GSM)

Description

The CSFB Success Rate Based Handover (LTE to GSM) KPI indicates the success rate of handover-based LTE-to-GSM CSFB.
The number of handover-based LTE-to-GSM CSFB attempts increases by 1 at point B as shown in Figure 1 after the eNodeB sends a Mobility From EUTRA Command message to the UE and performs CSFB to a GSM network. The number of successful handover-based LTE-to-GSM CSFB executions increases by 1 at point C, where the eNodeB receives a UE CONTEXT RELEASE COMMAND message from the MME after the UE successfully accesses the GSM network.

Definition

The CSFB Success Rate Based Handover (LTE to GSM) KPI is defined in Table 1. The number of handover-based LTE-to-GSM CSFB attempts and the number of successful handover-based LTE-to-GSM CSFB executions are collected as described in Description.

Table 1 CSFB Success Rate Based Handover (LTE to GSM)
Name CSFB Success Rate Based Handover (LTE to GSM)
Object Cell or radio network
Formula CSFB_L2G_BasedHO_SR = (CSFB_L2G_BasedHO_Success/CSFB_L2G_BasedHO_Attempt) x 100%
Associated Counters CSFB Success Rate Based Handover(LTE to GSM) = (L.IRATHO.E2G.CSFB.ExecSuccOut/L.IRATHO.E2G.CSFB.ExecAttOut) x 100%
Unit/Range Percentage (%)

CSFB Success Rate Based Handover (LTE to WCDMA)

 

Description

The CSFB Success Rate Based Handover (LTE to WCDMA) KPI indicates the success rate of handover-based LTE-to-WCDMA CSFB.
The number of handover-based LTE-to-WCDMA CSFB attempts increases by 1 at point B as shown in Figure 1 after the eNodeB sends a Mobility From EUTRA Command message to the UE and performs CSFB to a WCDMA network. The number of successful handover-based LTE-to-WCDMA CSFB executions increases by 1 at point C, where the eNodeB receives a UE CONTEXT RELEASE COMMAND message from the MME after the UE successfully accesses the WCDMA network.

Definition

The CSFB Success Rate Based Handover (LTE to WCDMA) KPI is defined in Table 1. The number of handover-based LTE-to-WCDMA CSFB attempts and the number of successful handover-based LTE-to-WCDMA CSFB executions are collected as described in Description.

Table 1 CSFB Success Rate Based Handover (LTE to WCDMA)
Name CSFB Success Rate Based Handover (LTE to WCDMA)
Object Cell or radio network
Formula CSFB_L2W_BasedHO_SR = (CSFB_L2W_BasedHO_Success/CSFB_L2W_BasedHO_Attempt) x 100%
Associated Counters CSFB Success Rate Based Handover(LTE to WCDMA) =(L.IRATHO.E2W.CSFB.ExecSuccOut/L.IRATHO.E2W.CSFB.ExecAttOut) x 100%
Unit/Range Percentage (%)
Note None

CSFB Success Rate Based Handover (LTE to WCDMA)

CSFB Success Rate Based Handover (LTE to WCDMA)

 

Description

The CSFB Success Rate Based Handover (LTE to WCDMA) KPI indicates the success rate of handover-based LTE-to-WCDMA CSFB.
The number of handover-based LTE-to-WCDMA CSFB attempts increases by 1 at point B as shown in Figure 1 after the eNodeB sends a Mobility From EUTRA Command message to the UE and performs CSFB to a WCDMA network. The number of successful handover-based LTE-to-WCDMA CSFB executions increases by 1 at point C, where the eNodeB receives a UE CONTEXT RELEASE COMMAND message from the MME after the UE successfully accesses the WCDMA network.

Definition

The CSFB Success Rate Based Handover (LTE to WCDMA) KPI is defined in Table 1. The number of handover-based LTE-to-WCDMA CSFB attempts and the number of successful handover-based LTE-to-WCDMA CSFB executions are collected as described in Description.

Table 1 CSFB Success Rate Based Handover (LTE to WCDMA)
Name CSFB Success Rate Based Handover (LTE to WCDMA)
Object Cell or radio network
Formula CSFB_L2W_BasedHO_SR = (CSFB_L2W_BasedHO_Success/CSFB_L2W_BasedHO_Attempt) x 100%
Associated Counters CSFB Success Rate Based Handover(LTE to WCDMA) =(L.IRATHO.E2W.CSFB.ExecSuccOut/L.IRATHO.E2W.CSFB.ExecAttOut) x 100%
Unit/Range Percentage (%)
Note None

Average CPU Load

Description

The Average CPU Load KPI indicates the CPU usage during busy hours.

Definition

The Average CPU Load KPI is defined in Table 1. The CPU load is calculated by averaging the CPU usage ratio during the measurement period.
Table 1 Average CPU Load
Name Average CPU Load
Object CPU
Formula MeanCPUUtility
Associated Counters Average CPU Load = VS.BBUBoard.CPULoad.Mean
Unit/Range Percentage (%)

Average CPU Load -- LTE

Average CPU Load

Description

The Average CPU Load KPI indicates the CPU usage during busy hours.

Definition

The Average CPU Load KPI is defined in Table 1. The CPU load is calculated by averaging the CPU usage ratio during the measurement period.
Table 1 Average CPU Load
Name Average CPU Load
Object CPU
Formula MeanCPUUtility
Associated Counters Average CPU Load = VS.BBUBoard.CPULoad.Mean
Unit/Range Percentage (%)

Uplink Preschedule Resource Block Occupied Rate

Description

The Uplink Preschedule Resource Block Occupied Rate KPI indicates the percentage of uplink RBs allocated to UEs for pre-scheduling. The Uplink Preschedule Resource Block Occupied Rate KPI can be used to evaluate the impact on uplink RB usage caused by pre-scheduling.
If pre-scheduling is enabled, when there are remaining uplink RBs in a cell, the eNodeB allocates uplink RBs to UEs that have not sent a bandwidth request to reduce the uplink service delay of these UEs.

Definition

The Uplink Preschedule Resource Block Occupied Rate KPI is defined in Table 1.
Table 1 Uplink Preschedule Resource Block Occupied Rate
Name Uplink Preschedule Resource Block Occupied Rate
Object Cell/Radio Network
Formula PrescheduleRB_URUL = RB_PrescheduleUsedUL/RB_AvailableUL
Associated Counters Uplink Preschedule Resource Block Occupied Rate= L.ChMeas.PRB.UL.PreSch.Used.Avg/L.ChMeas.PRB.UL.Avail
Unit/Range Percentage (%)
Note None

Uplink Preschedule Resource Block Occupied Rate --LTE

Uplink Preschedule Resource Block Occupied Rate

Description

The Uplink Preschedule Resource Block Occupied Rate KPI indicates the percentage of uplink RBs allocated to UEs for pre-scheduling. The Uplink Preschedule Resource Block Occupied Rate KPI can be used to evaluate the impact on uplink RB usage caused by pre-scheduling.
If pre-scheduling is enabled, when there are remaining uplink RBs in a cell, the eNodeB allocates uplink RBs to UEs that have not sent a bandwidth request to reduce the uplink service delay of these UEs.

Definition

The Uplink Preschedule Resource Block Occupied Rate KPI is defined in Table 1.
Table 1 Uplink Preschedule Resource Block Occupied Rate
Name Uplink Preschedule Resource Block Occupied Rate
Object Cell/Radio Network
Formula PrescheduleRB_URUL = RB_PrescheduleUsedUL/RB_AvailableUL
Associated Counters Uplink Preschedule Resource Block Occupied Rate= L.ChMeas.PRB.UL.PreSch.Used.Avg/L.ChMeas.PRB.UL.Avail
Unit/Range Percentage (%)
Note None

Resource Block Utilizing Rate

Description

The Resource Block Utilizing Rate KPI consists of two sub-KPIs: the uplink resource block (RB) utilizing rate and downlink RB utilizing rate. These two sub-KPIs indicate the busy-hour DL and UL RB utilizing rates in each cell or radio network.

Definition

The uplink and downlink Resource Block Utilizing Rate KPIs are defined in Table 1.
Table 1 Resource Block Utilizing Rate
Name Resource Block Utilizing Rate
Object Cell or radio network
Formula RB_URDL = (RB_UsedDL/RB_AvailableDL) x 100%
RB_URUL = (RB_UsedUL/RB_AvailableUL) x 100%
Associated Counters Downlink Resource Block Utilizing Rate =(L.ChMeas.PRB.DL.Used.Avg/L.ChMeas.PRB.DL.Avail) x 100%
Uplink Resource Block Utilizing Rate =(L.ChMeas.PRB.UL.Used.Avg/L.ChMeas.PRB.UL.Avail) x 100%
Unit/Range Percentage (%)
Note None

Resource Block Utilizing Rate -- LTE

Resource Block Utilizing Rate

Description

The Resource Block Utilizing Rate KPI consists of two sub-KPIs: the uplink resource block (RB) utilizing rate and downlink RB utilizing rate. These two sub-KPIs indicate the busy-hour DL and UL RB utilizing rates in each cell or radio network.

Definition

The uplink and downlink Resource Block Utilizing Rate KPIs are defined in Table 1.
Table 1 Resource Block Utilizing Rate
Name Resource Block Utilizing Rate
Object Cell or radio network
Formula RB_URDL = (RB_UsedDL/RB_AvailableDL) x 100%
RB_URUL = (RB_UsedUL/RB_AvailableUL) x 100%
Associated Counters Downlink Resource Block Utilizing Rate =(L.ChMeas.PRB.DL.Used.Avg/L.ChMeas.PRB.DL.Avail) x 100%
Uplink Resource Block Utilizing Rate =(L.ChMeas.PRB.UL.Used.Avg/L.ChMeas.PRB.UL.Avail) x 100%
Unit/Range Percentage (%)
Note None

Maximum User Number

Description

The Maximum User Number KPI evaluates the maximum number of users in RRC_Connected mode of a cell in a certain period of time. This value is calculated based on samples. The eNodeB records the number of users in the cell to be sampled every second and then calculates the maximum value of these samples throughout the measurement period.

Definition

The Maximum User Number KPI is defined in Table 1. The formula is mapped to its corresponding counters.
Table 1 Maximum User Number
Name Maximum User Number
Object Cell or radio network
Formula MaxUserNumber
Associated Counters Maximum User Number = L.Traffic.User.Max
Unit/Range NA
Note None

Maximum User Number -- LTE

Maximum User Number

Description

The Maximum User Number KPI evaluates the maximum number of users in RRC_Connected mode of a cell in a certain period of time. This value is calculated based on samples. The eNodeB records the number of users in the cell to be sampled every second and then calculates the maximum value of these samples throughout the measurement period.

Definition

The Maximum User Number KPI is defined in Table 1. The formula is mapped to its corresponding counters.
Table 1 Maximum User Number
Name Maximum User Number
Object Cell or radio network
Formula MaxUserNumber
Associated Counters Maximum User Number = L.Traffic.User.Max
Unit/Range NA
Note None

Average User Number

Description

The Average User Number KPI indicates the average number of users in RRC_Connected mode in a cell. This value is calculated based on samples. The eNodeB records the number of users in the cell to be sampled every second and then calculates the average value of these samples throughout the measurement period.

Definition

The Average User Number KPI is defined in Table 1. The formula is mapped to its corresponding counters.
Table 1 Average User Number
Name Average User Number
Object Cell or radio network
Formula AvgUserNumber
Associated Counters Average User Number = L.Traffic.User.Avg
Unit/Range NA
Note None

Average User Number --LTE

Average User Number

Description

The Average User Number KPI indicates the average number of users in RRC_Connected mode in a cell. This value is calculated based on samples. The eNodeB records the number of users in the cell to be sampled every second and then calculates the average value of these samples throughout the measurement period.

Definition

The Average User Number KPI is defined in Table 1. The formula is mapped to its corresponding counters.
Table 1 Average User Number
Name Average User Number
Object Cell or radio network
Formula AvgUserNumber
Associated Counters Average User Number = L.Traffic.User.Avg
Unit/Range NA
Note None

Uplink Traffic Volume

Description

Similar to the Downlink Traffic Volume KPI, the Uplink Traffic Volume KPI consists of ten sub-KPIs. One KPI corresponds to the total of traffic volume for DRBs, and the other nine correspond to nine QCIs. This set of sub-KPIs indicates a cell's uplink traffic volume. The sub-KPIs are measured at the PDCP layer and exclude the PDCP header.

Definition

The Uplink Traffic Volume KPIs are defined in Table 1 and include ten sub-KPIs. The formula for each KPI is mapped to its corresponding counter.
Table 1 Uplink Traffic Volume
Name Uplink Traffic Volume
Object Cell or radio network
Formula ULTraffic Volume
ULTraffic Volume_QCI_1
ULTraffic Volume_QCI_2
ULTraffic Volume_QCI_3
ULTraffic Volume_QCI_4
ULTraffic Volume_QCI_5
ULTraffic Volume_QCI_6
ULTraffic Volume_QCI_7
ULTraffic Volume_QCI_8
ULTraffic Volume_QCI_9
Associated Counters Uplink Traffic Volume = L.Thrp.bits.UL
Uplink Traffic Volume of QCIn = L.Thrp.bits.UL.QCI.n
n = 1 to 9
Unit/Range bit
Note None

Uplink Traffic Volume -- LTE

Uplink Traffic Volume

Description

Similar to the Downlink Traffic Volume KPI, the Uplink Traffic Volume KPI consists of ten sub-KPIs. One KPI corresponds to the total of traffic volume for DRBs, and the other nine correspond to nine QCIs. This set of sub-KPIs indicates a cell's uplink traffic volume. The sub-KPIs are measured at the PDCP layer and exclude the PDCP header.

Definition

The Uplink Traffic Volume KPIs are defined in Table 1 and include ten sub-KPIs. The formula for each KPI is mapped to its corresponding counter.
Table 1 Uplink Traffic Volume
Name Uplink Traffic Volume
Object Cell or radio network
Formula ULTraffic Volume
ULTraffic Volume_QCI_1
ULTraffic Volume_QCI_2
ULTraffic Volume_QCI_3
ULTraffic Volume_QCI_4
ULTraffic Volume_QCI_5
ULTraffic Volume_QCI_6
ULTraffic Volume_QCI_7
ULTraffic Volume_QCI_8
ULTraffic Volume_QCI_9
Associated Counters Uplink Traffic Volume = L.Thrp.bits.UL
Uplink Traffic Volume of QCIn = L.Thrp.bits.UL.QCI.n
n = 1 to 9
Unit/Range bit
Note None

Downlink Traffic Volume

Description

Similar to the Radio Bearers KPI, the Downlink Traffic Volume KPI consists of ten sub-KPIs. One KPI corresponds to the total DRB traffic volume, and the other nine correspond to nine QCIs. This set of sub-KPIs indicates the downlink traffic volume in a cell, which is measured at the PDCP layer and excludes the PDCP header.

Definition

The Downlink Traffic Volume KPIs are defined in Table 1 and include ten sub-KPIs. The formula for each KPI is mapped to its corresponding counter.
Table 1 Downlink Traffic Volume
Name Downlink Traffic Volume
Object Cell or radio network
Formula DLTrafficVolume
DLTrafficVolume_QCI_1
DLTrafficVolume_QCI_2
DLTrafficVolume_QCI_3
DLTrafficVolume_QCI_4
DLTrafficVolume_QCI_5
DLTrafficVolume_QCI_6
DLTrafficVolume_QCI_7
DLTrafficVolume_QCI_8
DLTrafficVolume_QCI_9
Associated Counters Downlink Traffic Volume = L.Thrp.bits.DL
Downlink Traffic Volume of QCIn = L.Thrp.bits.DL.QCI.n
n = 1 to 9
Unit/Range bit
Note None

Downlink Traffic Volume -- LTE

Downlink Traffic Volume

Description

Similar to the Radio Bearers KPI, the Downlink Traffic Volume KPI consists of ten sub-KPIs. One KPI corresponds to the total DRB traffic volume, and the other nine correspond to nine QCIs. This set of sub-KPIs indicates the downlink traffic volume in a cell, which is measured at the PDCP layer and excludes the PDCP header.

Definition

The Downlink Traffic Volume KPIs are defined in Table 1 and include ten sub-KPIs. The formula for each KPI is mapped to its corresponding counter.
Table 1 Downlink Traffic Volume
Name Downlink Traffic Volume
Object Cell or radio network
Formula DLTrafficVolume
DLTrafficVolume_QCI_1
DLTrafficVolume_QCI_2
DLTrafficVolume_QCI_3
DLTrafficVolume_QCI_4
DLTrafficVolume_QCI_5
DLTrafficVolume_QCI_6
DLTrafficVolume_QCI_7
DLTrafficVolume_QCI_8
DLTrafficVolume_QCI_9
Associated Counters Downlink Traffic Volume = L.Thrp.bits.DL
Downlink Traffic Volume of QCIn = L.Thrp.bits.DL.QCI.n
n = 1 to 9
Unit/Range bit
Note None

Radio Bearers

Description

The Radio Bearers KPI consists of ten sub-KPIs. One KPI corresponds to the total of radio bearers and the other nine correspond to nine QCIs. This set of sub-KPIs indicates the average number of radio bearers in a cell or radio network. The radio bearer for each QCI is based on the number of active RRC connections for each QCI, according to the QCI defined in the QoS information.

Definition

The Radio Bearers KPIs are defined in Table 1 and include ten different sub-KPIs. The formula for each KPI is mapped to its corresponding counter.
Table 1 Radio Bearers
Name Radio Bearers
Object Cell or radio network
Formula RadioBearers
RadioBearers_QCI_1
RadioBearers_QCI_2
RadioBearers_QCI_3
RadioBearers_QCI_4
RadioBearers_QCI_5
RadioBearers_QCI_6
RadioBearers_QCI_7
RadioBearers_QCI_8
RadioBearers_QCI_9
Associated Counters Radio Bearers =L.Traffic.DRB
RadioBearers of QCIn = L.Traffic.DRB.QCI.n
n = 1 to 9
Unit/Range NA
Note None

Radio Bearers -- LTE

Radio Bearers

Description

The Radio Bearers KPI consists of ten sub-KPIs. One KPI corresponds to the total of radio bearers and the other nine correspond to nine QCIs. This set of sub-KPIs indicates the average number of radio bearers in a cell or radio network. The radio bearer for each QCI is based on the number of active RRC connections for each QCI, according to the QCI defined in the QoS information.

Definition

The Radio Bearers KPIs are defined in Table 1 and include ten different sub-KPIs. The formula for each KPI is mapped to its corresponding counter.
Table 1 Radio Bearers
Name Radio Bearers
Object Cell or radio network
Formula RadioBearers
RadioBearers_QCI_1
RadioBearers_QCI_2
RadioBearers_QCI_3
RadioBearers_QCI_4
RadioBearers_QCI_5
RadioBearers_QCI_6
RadioBearers_QCI_7
RadioBearers_QCI_8
RadioBearers_QCI_9
Associated Counters Radio Bearers =L.Traffic.DRB
RadioBearers of QCIn = L.Traffic.DRB.QCI.n
n = 1 to 9
Unit/Range NA
Note None

Inter-Frequency Handover Out Success Rate

Description

The Inter-Frequency Handover Out Success Rate KPI indicates the success rate of inter-frequency handovers (HOs) from the local cell to neighboring E-UTRAN cells. The measurement methods of the related counters are similar to those for intra-frequency HOs described in Intra-Frequency Handover Out Success Rate > Description. The only difference is that the source and target cells operate on different frequencies and both work in FDD or TDD mode.

Figure 1 and Figure 2 illustrate intra-eNodeB HOs, and the source and target cells operate on different frequencies. The source eNodeB counts the number of intra-eNodeB inter-frequency outgoing HO execution attempts in the source cell at point B and counts the number of successful intra-eNodeB inter-frequency HO executions in the source cell at point C. Figure 3, Figure 4, Figure 5, Figure 6, Figure 7, and Figure 8 illustrate inter-eNodeB HOs, and the source and target cells operate on different frequencies. The source eNodeB counts the number of inter-eNodeB inter-frequency outgoing HO execution attempts in the source cell at point B and counts the number of successful inter-eNodeB inter-frequency HO executions in the source cell at point C.
 

Definition

The Inter-Frequency Handover Out Success Rate KPI is defined in Table 1. Note that the number of outgoing HO execution attempts and the number of successful outgoing HO executions are collected based on the description in Description.
Table 1 Inter-Frequency Handover Out Success Rate
Name Inter-Frequency Handover Out Success Rate
Object Cell or radio network
Formula InterFreqHOOut_SR = (InterFreqHOOutSuccess/InterFreqHOOutAttempt) x 100%
Associated Counters Inter-Frequency Handover Out Success Rate = [(L.HHO.IntraeNB.InterFreq.ExecSuccOut + L.HHO.IntereNB.InterFreq.ExecSuccOut)/(L.HHO.IntraeNB.InterFreq.ExecAttOut + L.HHO.IntereNB.InterFreq.ExecAttOut)] x 100%
Unit Percentage (%)
Note None

Inter-Frequency Handover Out Success Rate -- LTE

Inter-Frequency Handover Out Success Rate

Description

The Inter-Frequency Handover Out Success Rate KPI indicates the success rate of inter-frequency handovers (HOs) from the local cell to neighboring E-UTRAN cells. The measurement methods of the related counters are similar to those for intra-frequency HOs described in Intra-Frequency Handover Out Success Rate > Description. The only difference is that the source and target cells operate on different frequencies and both work in FDD or TDD mode.

Figure 1 and Figure 2 illustrate intra-eNodeB HOs, and the source and target cells operate on different frequencies. The source eNodeB counts the number of intra-eNodeB inter-frequency outgoing HO execution attempts in the source cell at point B and counts the number of successful intra-eNodeB inter-frequency HO executions in the source cell at point C. Figure 3, Figure 4, Figure 5, Figure 6, Figure 7, and Figure 8 illustrate inter-eNodeB HOs, and the source and target cells operate on different frequencies. The source eNodeB counts the number of inter-eNodeB inter-frequency outgoing HO execution attempts in the source cell at point B and counts the number of successful inter-eNodeB inter-frequency HO executions in the source cell at point C.
 

Definition

The Inter-Frequency Handover Out Success Rate KPI is defined in Table 1. Note that the number of outgoing HO execution attempts and the number of successful outgoing HO executions are collected based on the description in Description.
Table 1 Inter-Frequency Handover Out Success Rate
Name Inter-Frequency Handover Out Success Rate
Object Cell or radio network
Formula InterFreqHOOut_SR = (InterFreqHOOutSuccess/InterFreqHOOutAttempt) x 100%
Associated Counters Inter-Frequency Handover Out Success Rate = [(L.HHO.IntraeNB.InterFreq.ExecSuccOut + L.HHO.IntereNB.InterFreq.ExecSuccOut)/(L.HHO.IntraeNB.InterFreq.ExecAttOut + L.HHO.IntereNB.InterFreq.ExecAttOut)] x 100%
Unit Percentage (%)
Note None

Intra-Frequency Handover Out Success Rate

Description

The Intra-Frequency Handover Out Success Rate KPI indicates the success rate of intra-frequency handovers (HOs) from the local cell to neighboring E-UTRAN cells. The intra-frequency HOs are classified into intra- and inter-eNodeB HOs.

Intra-eNodeB Outgoing HO
Intra-eNodeB outgoing HOs can be further classified into HO with RRC connection reestablishment and HO without RRC connection reestablishment.
  • Intra-eNodeB outgoing HO without RRC connection reestablishment
    Figure 1 illustrates an intra-eNodeB outgoing HO without RRC connection reestablishment, and the source and target cells operate at the same frequency. When the eNodeB sends an RRC Connection Reconfiguration message containing the handover command to the UE, the eNodeB counts the number of intra-eNodeB intra-frequency HO outgoing execution attempts in the source cell at point B. When the eNodeB receives an RRC Connection Reconfiguration Complete message from the UE, the eNodeB counts the number of successful intra-eNodeB intra-frequency outgoing HO executions in the source cell at point C. 
    Figure 1 Intra-eNodeB outgoing HO without RRC connection reestablishment
  • Intra-eNodeB outgoing HO with RRC connection reestablishment
    Figure 2 illustrates an intra-eNodeB outgoing HO with RRC connection reestablishment, and the source and target cells operate at the same frequency. When the eNodeB sends an RRC Connection Reconfiguration message containing the handover command to the UE, the eNodeB counts the number of intra-eNodeB intra-frequency outgoing HO execution attempts in the source cell at point B. When the eNodeB receives an RRC Connection Reestablishment Complete message from the UE, the eNodeB counts the number of successful intra-eNodeB intra-frequency outgoing HO executions in the source cell at point C.
    Figure 2 Intra-eNodeB outgoing HO with RRC connection reestablishment
Inter-eNodeB Outgoing HO
Inter-eNodeB outgoing HOs can be further classified into HO without RRC connection reestablishment, HO with RRC connection reestablishment to the target cell, and HO with RRC connection reestablishment to the source cell.
  • Inter-eNodeB outgoing HO without RRC connection reestablishment
    Figure 3 and Figure 4 illustrate X2- and S1-based outgoing HOs without RRC connection reestablishment, respectively, and the source cell and target cell operate on the same frequency. When the source eNodeB sends an RRC Connection Reconfiguration message containing the handover command to the UE, the source eNodeB counts the number of intra-frequency outgoing HO execution attempts in the source cell at point B. When the source eNodeB receives a UE Context Release message from the target eNodeB or receives a UE Context Release Command message from the MME, indicating that the UE successfully accesses the target cell, the source eNodeB counts the number of successful intra-frequency outgoing HO executions in the source cell at point C. 
     
  • Inter-eNodeB outgoing HO with RRC connection reestablishment to the target cell
    Figure 5 and Figure 6 illustrate X2- and S1-based outgoing HOs with RRC connection reestablishment to the target cell, respectively, and the source cell and target cell operate on the same frequency. When the source eNodeB sends an RRC Connection Reconfiguration message containing the handover command to the UE, the source eNodeB counts the number of intra-frequency outgoing HO execution attempts in the source cell at point B. When the source eNodeB receives a UE Context Release message from the target eNodeB or receives a UE Context Release Command message from the MME, indicating that the UE successfully accesses the target cell, the source eNodeB counts the number of successful intra-frequency HO executions in the source cell at point C. 
     
  • Inter-eNodeB outgoing HO with RRC connection reestablishment to the source cell
    Figure 7 and Figure 8 illustrate X2- and S1-based outgoing HOs with RRC connection reestablishment to the source cell, respectively, and the source cell and target cell operate on the same frequency. When the source eNodeB sends an RRC Connection Reconfiguration message containing the handover command to the UE, the source eNodeB counts the number of intra-frequency outgoing HO execution attempts in the source cell at point B. When the source eNodeB receives an RRC Connection Reestablishment Complete message from the UE, the source eNodeB counts the number of successful intra-frequency outgoing HO executions in the source cell at point C. 
     

Definition

The Intra-Frequency Handover Out Success Rate KPI is defined in Table 1. Note that the number of outgoing HO execution attempts and the number of successful outgoing HO executions are collected based on the description in Description.
Table 1 Intra-Frequency Handover Out Success Rate
Name Intra-Frequency Handover Out Success Rate
Object Cell or radio network
Formula IntraFreqHOOut_SR = (IntraFreqHOOutSuccess/IntraFreqHOOutAttempt) x 100%
Associated Counters Intra-Frequency Handover Out Success Rate = [(L.HHO.IntraeNB.IntraFreq.ExecSuccOut + L.HHO.IntereNB.IntraFreq.ExecSuccOut)/(L.HHO.IntraeNB.IntraFreq.ExecAttOut + L.HHO.IntereNB.IntraFreq.ExecAttOut)] x 100%
Unit Percentage (%)
Note None

Intra-Frequency Handover Out Success Rate -- LTE

Intra-Frequency Handover Out Success Rate

Description

The Intra-Frequency Handover Out Success Rate KPI indicates the success rate of intra-frequency handovers (HOs) from the local cell to neighboring E-UTRAN cells. The intra-frequency HOs are classified into intra- and inter-eNodeB HOs.

Intra-eNodeB Outgoing HO
Intra-eNodeB outgoing HOs can be further classified into HO with RRC connection reestablishment and HO without RRC connection reestablishment.
  • Intra-eNodeB outgoing HO without RRC connection reestablishment
    Figure 1 illustrates an intra-eNodeB outgoing HO without RRC connection reestablishment, and the source and target cells operate at the same frequency. When the eNodeB sends an RRC Connection Reconfiguration message containing the handover command to the UE, the eNodeB counts the number of intra-eNodeB intra-frequency HO outgoing execution attempts in the source cell at point B. When the eNodeB receives an RRC Connection Reconfiguration Complete message from the UE, the eNodeB counts the number of successful intra-eNodeB intra-frequency outgoing HO executions in the source cell at point C. 
    Figure 1 Intra-eNodeB outgoing HO without RRC connection reestablishment
  • Intra-eNodeB outgoing HO with RRC connection reestablishment
    Figure 2 illustrates an intra-eNodeB outgoing HO with RRC connection reestablishment, and the source and target cells operate at the same frequency. When the eNodeB sends an RRC Connection Reconfiguration message containing the handover command to the UE, the eNodeB counts the number of intra-eNodeB intra-frequency outgoing HO execution attempts in the source cell at point B. When the eNodeB receives an RRC Connection Reestablishment Complete message from the UE, the eNodeB counts the number of successful intra-eNodeB intra-frequency outgoing HO executions in the source cell at point C.
    Figure 2 Intra-eNodeB outgoing HO with RRC connection reestablishment
Inter-eNodeB Outgoing HO
Inter-eNodeB outgoing HOs can be further classified into HO without RRC connection reestablishment, HO with RRC connection reestablishment to the target cell, and HO with RRC connection reestablishment to the source cell.
  • Inter-eNodeB outgoing HO without RRC connection reestablishment
    Figure 3 and Figure 4 illustrate X2- and S1-based outgoing HOs without RRC connection reestablishment, respectively, and the source cell and target cell operate on the same frequency. When the source eNodeB sends an RRC Connection Reconfiguration message containing the handover command to the UE, the source eNodeB counts the number of intra-frequency outgoing HO execution attempts in the source cell at point B. When the source eNodeB receives a UE Context Release message from the target eNodeB or receives a UE Context Release Command message from the MME, indicating that the UE successfully accesses the target cell, the source eNodeB counts the number of successful intra-frequency outgoing HO executions in the source cell at point C. 
     
  • Inter-eNodeB outgoing HO with RRC connection reestablishment to the target cell
    Figure 5 and Figure 6 illustrate X2- and S1-based outgoing HOs with RRC connection reestablishment to the target cell, respectively, and the source cell and target cell operate on the same frequency. When the source eNodeB sends an RRC Connection Reconfiguration message containing the handover command to the UE, the source eNodeB counts the number of intra-frequency outgoing HO execution attempts in the source cell at point B. When the source eNodeB receives a UE Context Release message from the target eNodeB or receives a UE Context Release Command message from the MME, indicating that the UE successfully accesses the target cell, the source eNodeB counts the number of successful intra-frequency HO executions in the source cell at point C. 
     
  • Inter-eNodeB outgoing HO with RRC connection reestablishment to the source cell
    Figure 7 and Figure 8 illustrate X2- and S1-based outgoing HOs with RRC connection reestablishment to the source cell, respectively, and the source cell and target cell operate on the same frequency. When the source eNodeB sends an RRC Connection Reconfiguration message containing the handover command to the UE, the source eNodeB counts the number of intra-frequency outgoing HO execution attempts in the source cell at point B. When the source eNodeB receives an RRC Connection Reestablishment Complete message from the UE, the source eNodeB counts the number of successful intra-frequency outgoing HO executions in the source cell at point C. 
     

Definition

The Intra-Frequency Handover Out Success Rate KPI is defined in Table 1. Note that the number of outgoing HO execution attempts and the number of successful outgoing HO executions are collected based on the description in Description.
Table 1 Intra-Frequency Handover Out Success Rate
Name Intra-Frequency Handover Out Success Rate
Object Cell or radio network
Formula IntraFreqHOOut_SR = (IntraFreqHOOutSuccess/IntraFreqHOOutAttempt) x 100%
Associated Counters Intra-Frequency Handover Out Success Rate = [(L.HHO.IntraeNB.IntraFreq.ExecSuccOut + L.HHO.IntereNB.IntraFreq.ExecSuccOut)/(L.HHO.IntraeNB.IntraFreq.ExecAttOut + L.HHO.IntereNB.IntraFreq.ExecAttOut)] x 100%
Unit Percentage (%)
Note None

Service Drop Rate (Always Online)

Description

The Service Drop Rate (Always Online) KPI indicates the call drop rate of all the services in a cell or radio network, including the VoIP services, when the always online state is active.
The Service Drop Rate (Always Online) KPI of all services is defined in Table 1.
Table 1 Service Drop Rate (Always Online)
Name Service Drop Rate (Always Online)
Object Cell or radio network
Formula AlwaysOnline_CDR = (ERABAbnormalReleaseOfAlwaysOnline/ERABReleaseOfAlwaysOnline) x 100%
Associated Counters Service Drop Rate (Always Online) =(L.E-RAB.AbnormRel/(L.E-RAB.AbnormRel + L.E-RAB.NormRel + L.E-RAB.Num.Syn2Unsyn)) x 100%
Unit/Range Percentage (%)
Note None

Service Drop Rate (Always Online) -- LTE

Service Drop Rate (Always Online)

Description

The Service Drop Rate (Always Online) KPI indicates the call drop rate of all the services in a cell or radio network, including the VoIP services, when the always online state is active.
The Service Drop Rate (Always Online) KPI of all services is defined in Table 1.
Table 1 Service Drop Rate (Always Online)
Name Service Drop Rate (Always Online)
Object Cell or radio network
Formula AlwaysOnline_CDR = (ERABAbnormalReleaseOfAlwaysOnline/ERABReleaseOfAlwaysOnline) x 100%
Associated Counters Service Drop Rate (Always Online) =(L.E-RAB.AbnormRel/(L.E-RAB.AbnormRel + L.E-RAB.NormRel + L.E-RAB.Num.Syn2Unsyn)) x 100%
Unit/Range Percentage (%)
Note None

Service Drop Rate (All)

Description

The Service Drop Rate (All) KPI indicates the call drop rate of all the services in a cell or radio network, including the VoIP service. Similar to the KPI defined in section 3.1 "Call Drop Rate (VoIP)", this KPI measures abnormal releases at the eNodeB.

Definition

The Service Drop Rate (All) KPI is defined in Table 1.
Table 1 Service Drop Rate (All)
Name Service Drop Rate (All)
Object Cell or radio network
Formula Service_CDR = (ERABAbnormalRelease/ERABRelease) x 100%
Associated Counters Service Drop Rate (All) =(L.E-RAB.AbnormRel/(L.E-RAB.AbnormRel + L.E-RAB.NormRel)) x 100%
Unit/Range Percentage (%)
Note None

Service Drop Rate (All) -- LTE

Service Drop Rate (All)

Description

The Service Drop Rate (All) KPI indicates the call drop rate of all the services in a cell or radio network, including the VoIP service. Similar to the KPI defined in section 3.1 "Call Drop Rate (VoIP)", this KPI measures abnormal releases at the eNodeB.

Definition

The Service Drop Rate (All) KPI is defined in Table 1.
Table 1 Service Drop Rate (All)
Name Service Drop Rate (All)
Object Cell or radio network
Formula Service_CDR = (ERABAbnormalRelease/ERABRelease) x 100%
Associated Counters Service Drop Rate (All) =(L.E-RAB.AbnormRel/(L.E-RAB.AbnormRel + L.E-RAB.NormRel)) x 100%
Unit/Range Percentage (%)
Note None

Call Drop Rate (VoIP)

Description

The Call Drop Rate (VoIP) KPI indicates the call drop rate of the VoIP services in a cell or radio network. A VoIP call drop occurs when the VoIP E-RAB is abnormally released. Each E-RAB is associated with QoS information. Usually, the QCI of VoIP services is 1.
An E-RAB consists of a radio bearer and a corresponding S1 bearer. Any abnormal release of either bearer causes a call drop. A release is defined as abnormal by its release cause according to 3GPP TS 36.413.
Abnormal E-RAB releases can be classified into the following two scenarios, as shown in Figure 1.
 
Figure 1 Abnormal E-RAB release
  • Scenario 1: When the eNodeB sends an E-RAB Release Indication message to the MME, the abnormal E-RAB release counter is incremented if the bearer to be released carries data and the release cause is not "Normal Release", "Detach", "User Inactivity", "CS Fallback triggered", "UE Not Available for PS Service", or "Inter-RAT Redirection".
  • Scenario 2: When the eNodeB sends a UE Context Release Request message to the MME, the abnormal E-RAB release counter is incremented if the bearer to be released carries data and the release cause is not "Normal Release", "Detach", "User Inactivity", "CS fallback triggered", "UE Not Available For PS Service", "Inter-RAT redirection", "Time Critical Handover", "Handover Cancelled".
 NOTE:
  • Except for the preceding two scenarios, the normal E-RAB release counter is incremented.
  • If the message contains several E-RAB ID IEs (in the E-RAB To Be Released List IE), the counter will be incremented for each individual E-RAB.

Definition

The Call Drop Rate (VoIP) KPI is defined in Table 1.
Table 1 Call Drop Rate (VoIP)
Name Call Drop Rate (VoIP)
Object Cell or radio network
Formula VoIP_CDR = (VoIPERABAbnormalRelease/VoIPERABRelease) x 100%
Associated Counters Call Drop Rate (VoIP) = [L.E-RAB.AbnormRel.QCI.1/(L.E-RAB.AbnormRel.QCI.1 + L.E-RAB.NormRel.QCI.1)] x 100%
Unit/Range Percentage (%)
Note None

Call Drop Rate (VoIP) -- LTE

Call Drop Rate (VoIP)

Description

The Call Drop Rate (VoIP) KPI indicates the call drop rate of the VoIP services in a cell or radio network. A VoIP call drop occurs when the VoIP E-RAB is abnormally released. Each E-RAB is associated with QoS information. Usually, the QCI of VoIP services is 1.
An E-RAB consists of a radio bearer and a corresponding S1 bearer. Any abnormal release of either bearer causes a call drop. A release is defined as abnormal by its release cause according to 3GPP TS 36.413.
Abnormal E-RAB releases can be classified into the following two scenarios, as shown in Figure 1.
 
Figure 1 Abnormal E-RAB release
  • Scenario 1: When the eNodeB sends an E-RAB Release Indication message to the MME, the abnormal E-RAB release counter is incremented if the bearer to be released carries data and the release cause is not "Normal Release", "Detach", "User Inactivity", "CS Fallback triggered", "UE Not Available for PS Service", or "Inter-RAT Redirection".
  • Scenario 2: When the eNodeB sends a UE Context Release Request message to the MME, the abnormal E-RAB release counter is incremented if the bearer to be released carries data and the release cause is not "Normal Release", "Detach", "User Inactivity", "CS fallback triggered", "UE Not Available For PS Service", "Inter-RAT redirection", "Time Critical Handover", "Handover Cancelled".
 NOTE:
  • Except for the preceding two scenarios, the normal E-RAB release counter is incremented.
  • If the message contains several E-RAB ID IEs (in the E-RAB To Be Released List IE), the counter will be incremented for each individual E-RAB.

Definition

The Call Drop Rate (VoIP) KPI is defined in Table 1.
Table 1 Call Drop Rate (VoIP)
Name Call Drop Rate (VoIP)
Object Cell or radio network
Formula VoIP_CDR = (VoIPERABAbnormalRelease/VoIPERABRelease) x 100%
Associated Counters Call Drop Rate (VoIP) = [L.E-RAB.AbnormRel.QCI.1/(L.E-RAB.AbnormRel.QCI.1 + L.E-RAB.NormRel.QCI.1)] x 100%
Unit/Range Percentage (%)
Note None

Call Setup Success Rate

Description

The Call Setup Success Rate KPI indicates the call setup success rate for all services, including the VoIP service in a cell or radio network. This KPI is calculated based on the RRC Setup Success Rate (Service) KPI, the S1 Signaling Connection Setup Success Rate KPI, and the E-RAB Setup Success Rate (All) KPI.

Definition

The Call Setup Success Rate KPI is defined in Table 1. The KPI is calculated by multiplying the RRC Setup Success Rate (Service) KPI, the S1 Signaling Connection Setup Success Rate KPI, and the E-RAB Setup Success Rate (All) KPI.

Table 1 Call Setup Success Rate
Name Call Setup Success Rate
Object Cell or radio network
Formula CSSR = (RRCConnectionSuccessservice/RRCConnectionAttemptservice) x (S1SIGConnectionEstablishSuccess/S1SIGConnectionEstablishAttempt) x (ERABSetupSuccess/ERABSetupAttempt) x 100%
Associated Counters Call Setup Success Rate =((L.RRC.ConnReq.Succ.Emc + L.RRC.ConnReq.Succ.HighPri + L.RRC.ConnReq.Succ.Mt + L.RRC.ConnReq.Succ.MoData + L.RRC.ConnReq.Succ.DelayTol)/(L.RRC.ConnReq.Att.Emc + L.RRC.ConnReq.Att.HighPri + L.RRC.ConnReq.Att.Mt + L.RRC.ConnReq.Att.MoData + L.RRC.ConnReq.Att.DelayTol)) x (L.S1Sig.ConnEst.Succ/L.S1Sig.ConnEst.Att) x (L.E-RAB.SuccEst/L.E-RAB.AttEst) x 100%
Unit/Range Percentage (%)

LTE Call Setup Success Rate

Call Setup Success Rate

Description

The Call Setup Success Rate KPI indicates the call setup success rate for all services, including the VoIP service in a cell or radio network. This KPI is calculated based on the RRC Setup Success Rate (Service) KPI, the S1 Signaling Connection Setup Success Rate KPI, and the E-RAB Setup Success Rate (All) KPI.

Definition

The Call Setup Success Rate KPI is defined in Table 1. The KPI is calculated by multiplying the RRC Setup Success Rate (Service) KPI, the S1 Signaling Connection Setup Success Rate KPI, and the E-RAB Setup Success Rate (All) KPI.

Table 1 Call Setup Success Rate
Name Call Setup Success Rate
Object Cell or radio network
Formula CSSR = (RRCConnectionSuccessservice/RRCConnectionAttemptservice) x (S1SIGConnectionEstablishSuccess/S1SIGConnectionEstablishAttempt) x (ERABSetupSuccess/ERABSetupAttempt) x 100%
Associated Counters Call Setup Success Rate =((L.RRC.ConnReq.Succ.Emc + L.RRC.ConnReq.Succ.HighPri + L.RRC.ConnReq.Succ.Mt + L.RRC.ConnReq.Succ.MoData + L.RRC.ConnReq.Succ.DelayTol)/(L.RRC.ConnReq.Att.Emc + L.RRC.ConnReq.Att.HighPri + L.RRC.ConnReq.Att.Mt + L.RRC.ConnReq.Att.MoData + L.RRC.ConnReq.Att.DelayTol)) x (L.S1Sig.ConnEst.Succ/L.S1Sig.ConnEst.Att) x (L.E-RAB.SuccEst/L.E-RAB.AttEst) x 100%
Unit/Range Percentage (%)

E-RAB Setup Success Rate (All)

Description

The E-RAB Setup Success Rate (All) KPI indicates the E-RAB setup success rate for all services, including the VoIP service in a cell or radio network. This KPI is calculated based on the counters (both the E-RAB connection setup attempts [all] and the successful E-RAB setup [all] counters) measured at the eNodeB, as shown in Figure 1.

Definition

The E-RAB Setup Success Rate (All) KPI is defined in Table 1. The number of E-RAB connection setup attempts (all) and the number of successful E-RAB setup counters (all) are collected based on the description in Description.
Table 1 E-RAB Setup Success Rate (All)
Name E-RAB Setup Success Rate (All)
Object Cell or radio network
Formula ERABS_SR = (ERABSetupSuccess/ERABSetupAttempt) x 100%
Associated Counters E-RAB Setup Success Rate (All) =(L.E-RAB.SuccEst/L.E-RAB.AttEst) x 100%
Unit/Range Percentage (%)
Note None

E-RAB Setup Success Rate (All)

E-RAB Setup Success Rate (All)

Description

The E-RAB Setup Success Rate (All) KPI indicates the E-RAB setup success rate for all services, including the VoIP service in a cell or radio network. This KPI is calculated based on the counters (both the E-RAB connection setup attempts [all] and the successful E-RAB setup [all] counters) measured at the eNodeB, as shown in Figure 1.

Definition

The E-RAB Setup Success Rate (All) KPI is defined in Table 1. The number of E-RAB connection setup attempts (all) and the number of successful E-RAB setup counters (all) are collected based on the description in Description.
Table 1 E-RAB Setup Success Rate (All)
Name E-RAB Setup Success Rate (All)
Object Cell or radio network
Formula ERABS_SR = (ERABSetupSuccess/ERABSetupAttempt) x 100%
Associated Counters E-RAB Setup Success Rate (All) =(L.E-RAB.SuccEst/L.E-RAB.AttEst) x 100%
Unit/Range Percentage (%)
Note None